Atex AR950 Operation Manual Download Page 42

Page: 42 / 106

3. Depress the brake pedal to “Unlock” the
parking brake lever.

4. Travel on the machine by depressing the HST

pedal forward or backward. The speed can be
adjusted according to depressing amout of the
HST pedal.

5. Travel on the machine by operating the HST

lever forward and backward. The speed can be
adjusted steplessly.

●

Move forward: Depress the HST pedal forward.

●

Move in reverse: Depress the HST pedal backward.

●

Move forward: Tilt the HST lever forward.

●

Move in reverse: Tilt the HST lever backward.

Warning

●

Don’t operate the HST lever and HST pedal at the same

time. Wrong operation may cause the machine to crash or
fall down.

●

Depressing the HST pedal in the wrong forward/reverse

direction or tilting the HST lever in the wrong forward/reverse
direction may cause the machine to crash or fall down. Pay
attention to correct operation.

●

When depressing the HST pedal, shift the HST lever to “Neutral”

position.

●

When shifting the HST lever, release the foot from the HST pedal.

How to Work

Brake pedal

Forward

HST Pedal

Reverse

HST lever

Reverse

Forward

Summary of Contents for AR950











































































































Search results

Summary of Contents for AR950

Reviews:

Related manuals for AR950

Brands by name

Popular brands

Atex AR950, Operation Manual

Search results

Summary of Contents for AR950

Reviews:

Related manuals for AR950

Brands by name

Popular brands