Atex AR950 Operation Manual Download Page 82

Page: 82 / 106

1. Shift the cutting-height adjustment lever to the

“Start Engine” position.

2. Loosen the lock nut and turn the adjusting bolt

until the tip of switch is pushed onto the nut

surface. After the adjustment, tighten up the lock

nut to

x adjusting bolt.

(2) Adjusting the Safety Switch for the Cutting Blade

(3) Adjusting the Safety Switch for the Seat

When the safety switch brakes down, ask the “dealer from which you purchased your
Ride-on Bush Cutter” to inspect the machine and make adjustment.

(4) Inspecting the Operation of Each Safety Switch

Check the movement of the tip of safety switch
and if it is defective, apply spray grease on the
moving part. If the movement is not smooth,
replace the safety switch.

Cutting-height adjustment lever

Start engine

Adjusting bolt

Lock nut

Grease

How to Work

Summary of Contents for AR950











































































































Search results

Summary of Contents for AR950

Reviews:

Related manuals for AR950

Brands by name

Popular brands

Atex AR950, Operation Manual

Search results

Summary of Contents for AR950

Reviews:

Related manuals for AR950

Brands by name

Popular brands