manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 99

3. Heater ground connection (white)

4. Heater power supply (white)

THE CONNECTION DIAGRAMS ARE IN THE ELECTRICAL SYSTEM SECTIONS; PAY ATTENTION

TO THESE DIAGRAMS AS THEY SHOW THE CONNECTOR/COMPONENT AS VIEWED FROM

THE CABLE HARNESS SIDE, THAT IS LOOKING AT THE CABLES WHEN GOING OUT OF THE

"MAIN" CABLE HARNESS AND INTO THE CONNECTOR/COMPONENT.

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

AXONE: FUEL INJECTION SYSTEM

PARAMETERS

Lambda probe

Example value: 0 - 1000 mV

Signal when energised that the control unit receives from the lambda probe: inversely proportional to

the presence of oxygen.

Lambda integrator

Example value: 0,00 %

In closed loop, the value must be close to 0.00 (values not within the interval from -10.0 % to 10.0 %

indicate a fault): for example, value 25% corresponds to +25% with respect to the reference injection

time; -25% corresponds to -25%. In an open circuit, the lambda probe signal is too low. Therefore, the

control unit takes it as a lean mixture condition and will try to enrich it. The value read will be +25%:

once this correction has been tried, the value shifts to 0.00 fixed and the Lambda probe error is signalled.

STATUSES

Lambda

Example value:

Open loop / Closed loop

It indicates if the control unit is using (CLOSED) the lambda probe signal to keep the stoichiometric

combustion. At idle CLOSED only if: Air T >10° and engine T > 18° and engine running for at least 1-2

minutes.

ELECTRICAL ERRORS

Lambda probe P0130

 - shorted to positive / open circuit, shorted to negative.

Error cause

•

If shorted to positive, excessive voltage has been detected at PIN 22 of connector B (BLUE).

If the circuit is open, shorted to negative, no voltage has been detected. In both cases, the

recovery function is hardly noticeable for the customer.

Troubleshooting

MSS Mana GT ABS

Electrical system

ELE SYS - 99

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands