APRILIA MSS Mana GT ABS Service Station Manual Download Page 202

Page: 202 / 394

- Check that the centring dowel is correctly fitted

and push the cylinder until it stops.

Selecting the base gasket

- First fit the piston into the cylinder, without any base gasket.

- Fit a dial gauge on the specific tool with the short union, as shown in the figure.

Specific tooling

020714Y

Dial gauge mounting

- With a contrasting surface, reset the dial gauge

with a preloading of a few millimetres.

- Finally fix the dial gauge.

- Check the perfect sliding of the feeler pin.

- Fit the tool on the cylinder without changing the

dial gauge position.

- Lock the tool with the original head fixing nuts.

- Rotate the crankshaft up to TDC (the reversal

point of the dial gauge rotation).

- Measure the deviation from the reset value.

Engine

MSS Mana GT ABS

ENG - 202

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Search results

Summary of Contents for MSS Mana GT ABS

Reviews:

Brands by name

Popular brands

APRILIA MSS Mana GT ABS, Service Station Manual

Search results

Summary of Contents for MSS Mana GT ABS

Reviews:

Brands by name

Popular brands