manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 96

•

If the circuit is open, shorted to positive: excessive voltage has been detected at PIN 5 of

connector A (BROWN). If shorted to negative: voltage equal to zero has been detected. In

both cases, recovery function.

Troubleshooting

•

If the circuit is open, shorted to positive: check the sensor connector and the Marelli control

unit connector. If they are OK, check sensor continuity: replace the sensor if not OK; if it is

OK, check the continuity between PIN 5 of the connector A (BROWN) and sensor PIN 1:

restore cable harness if there is no continuity; if it is OK, reconnect the control unit connector

and, with key set to key ON, check the continuity between the sensor connector PIN 2 and

the vehicle ground connection: if it is OK, it means that the error cause is that the cable is

shorted to positive and it is necessary to restore the cable harness between ENGINE PIN

5 and sensor PIN 1; if there is not continuity with the ground lead, check the sensor connector

and the Marelli control unit connector; if they are not OK, restore the cable harness; if they

are OK, check continuity between PIN 20 of the connector A (BROWN) and PIN 2 of the

sensor connector: restore the cable harness if there is not continuity. If there is, it means

that the control unit does not supply the ground connection and therefore should be replaced.

•

If shorted to negative, check sensor correct resistance: if resistance is null, replace the sen-

sor; if resistance is correct, it means that the cable has ground connection: restore the cable

harness.

NOTES

 

No error is detected if the sensor does not work correctly or the control unit connector

or sensor terminals are rusty: then check through Navigator if the temperature indicated is the

same as the engine temperature. Check also that the sensor electrical characteristics are ob-

served: replace the sensor if not OK; if it is OK, check the sensor connector and the Marelli

control unit connector

Air temperature sensor

INTAKE AIR TEMPERATURE SENSOR

Function

It tells the control unit the intake air temperature in

order to calculate oxygen presence so as to opti-

mise the petrol quantity necessary for correct com-

bustion.

Operation / Operating principle

NTC type sensor (resistance sensor, inversely

variable with temperature).

Level in wiring diagram:

Temperature sensors

Location:

Electrical system

MSS Mana GT ABS

ELE SYS - 96

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands