manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 224

CONTINUE - point 2

2 -

 Remove the electric connector of the minimum pressure switch.

Check that the warning light turns off.

YES - point 3 NO point 11

3 -

 Check the actual oil pressure.

CONTINUE - point 4

4 -

 Remove the switch and fit the specific tool with the relevant gasket.

Specific tooling

020193Y

 

Gauge for oil pressure check

020434Y

 

Fitting for oil pressure check

- Remove the dipstick with the oil filler plug and insert a plug with the temperature probe supplied with

the specific tool. Insert the probe to feel contact with the crankcase bottom and pull back a few milli-

metres.

Specific tooling

020331Y

 

Digital multimeter

CONTINUE - point 5

5 -

 Measure pressure with cold and idling engine.

STANDARD VALUES

Specification

Desc./Quantity

20°C Temperature

1400 rpm

~ 4.5 bar

YES - point 6 NO point 12

6 -

 Let the engine warm up and repeat the check with hot oil.

STANDARD VALUES

Specification

Desc./Quantity

80°C Temperature

1400 rpm

~ 1.5 bar

YES - point 7 NO point 8

7 -

 Replace the minimum oil pressure.

Engine

MSS Mana GT ABS

ENG - 224

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands