manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 298

•

Fit the centring plate.

•

Fit the pumping member together with

the centring plate in the sleeve.

•

Insert the special washer in the screw.

•

Tighten the screw to the prescribed tor-

que.

UPON REFITTING, REPLACE THE SAFETY WASHER WITH
A NEW ONE

Locking torques (N*m)

Screw fixing the stem in wheel holder - M10x1.5
(2)

 

20 Nm (14.75 lbf ft)

Filling oil

NOTE

THE FOLLOWING OPERATIONS REFER TO THE MARZOCCHI FORKS.

RIGHT STEM

•

Place the stanchion on a work table in upright position.

•

Fill the sleeve with the adequate quality and type of oil indicated on the recommended prod-

ucts table.

WARNING

MOVE THE PUMPING ELEMENT SEVERAL TIMES UNTIL
AIR BUBBLES ARE SEEN ON THE OIL SURFACE.

Characteristic

Fork oil quantity (right stem) (Marzocchi)

490 cc (29.90 cu in)

Oil level (from sleeve rim, without the spring
with preload pipe and with stem at end of
stroke)

50 mm (1.97 in)

•

Insert the preload pipe.

Suspensions

MSS Mana GT ABS

SUSP - 298

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands