manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 210

Crankcase - crankshaft

- Remove the transmission cover, the driving and the driven pulleys, as described in the «Automatic

transmission» chapter.

- Remove the flywheel cover as described in the «Flywheel cover removal» chapter.

- Remove the magneto flywheel with the start-up control as described in the «Magneto flywheel re-

moval» chapter.

- Remove the thermal parts (cylinders, heads, pistons) as described in the «Thermal group and Timing

system» chapter.

- Before opening the engine crankcase, it is advisable to check the axial clearance of the crankshaft.

Specific tooling

020262Y

 

Crankcase splitting strip

020335Y

 

Dial gauge magnetic support

Characteristic

Standard clearance:

0.10 ÷ 0.50 mm

Increased limit after use:

0.60 mm

- Higher clearances are signs of wear on the supporting surfaces of the crankshaft on the crankcase.

- To carry out an accurate measurement, measure the clearance in both directions between crankcase

and crankshaft.

Engine

MSS Mana GT ABS

ENG - 210

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands