manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 389

Carry out the listed checks before delivering the motorcycle.

WARNING

HANDLE FUEL WITH CARE.

Aesthetic inspection

- Paintwork

- Fitting of Plastic Parts

- Scratches

- Dirt

Tightening torques inspection

- Safety fasteners:

front and rear suspension unit

front and rear brake calliper retainer unit

front and rear wheel unit

engine - chassis retainers

steering assembly

- Plastic parts fixing screws

Electrical system

- Main switch

- Headlamps: high beam lights, low beam lights, tail lights (front and rear) and their warning lights

- Headlight adjustment according to regulations in force

- Front and rear stop light switches and their bulbs

- Turn indicators and their warning lights

- Instrument panel lights

- Instrument panel: fuel and temperature indicator (if present)

- Instrument panel warning lights

- Horn

- Electric starter

- Engine stop via emergency stop switch and side stand

- Helmet compartment electrical opening switch (if present)

MSS Mana GT ABS

Pre-delivery

PRE DE - 389

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands