manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 41

km x 1,000

1

10

20

30

40

50

60

70

80

Engine oil

R

R

R

R

R

R

R

R

Fork oil seals

I

I

I

I

I

I

I

I

I

Brake pads (3)

I

I

I

I

I

I

I

I

I

Variator sliders

R

R

R

R

Parking brake calliper

I

I

I

I

I

I

I

I

I

Tyres

I

I

I

I

I

I

I

I

I

Tyre pressure

I

I

I

I

I

I

I

I

I

Wheels and transmission cush drive

I

I

I

I

I

I

I

I

I

Transmission screws and bolts torque tightening

I

I

I

I

I

I

I

I

Tightening bolts, nuts and screws

I

I

I

I

I

I

I

I

I

Suspension and setting

I

I

I

I

I

I

I

I

I

Final drive unit (chain, crown and pinion)

I

I

R

I

I

R

I

I

Fuel lines (2)

I

I

Labour time (minutes)

100

120

140

290

140

120

270

120

200

Spark plug

At regular intervals, remove the spark plug and clean off any carbon deposits or replace as required.

CAUTION

ALWAYS REPLACE BOTH SPARK PLUGS EVEN IF ONLY ONE NEEDS REPLACING.

In order to reach the spark plugs:

CAUTION

BEFORE CARRYING OUT THE FOLLOWING OPERATIONS AND IN ORDER TO AVOID BURNS,
LEAVE ENGINE AND SILENCER TO COOL OFF TO AMBIENT TEMPERATURE.

•

Working from both sides, remove the

two spark plug tubes.

•

With the specific supplied wrench, un-

screw and remove the spark plugs (two

per cylinder).

•

Check the gap between the electrodes

with a feeler gauge.

CAUTION

DO NOT ATTEMPT TO READJUST THE ELECTRODE GAP.

MSS Mana GT ABS

Maintenance

MAIN - 41

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands