manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 213

- Remove the tip.

Specific tooling

020664Y

 

Flywheel side crankshaft fitting tip

Removing the crankshaft

- Fit the specific tool on the transmission side

crankshaft, paying special attention that the tool

matches the shaft perfectly.

CAUTION

DUE TO THE TIP WEIGHT PAY ATTENTION TO THE COR-
RECT COUPLING AND FALLING RISKS OF THE TOOL,
ALWAYS HOLD IT WITH YOUR HANDS.

CAUTION

FAILURE TO OBSERVE THIS RULE CAN DAMAGE THE MAIN BUSHINGS.

Specific tooling

020665Y

 

Transmission side crankshaft fitting tip

- Lubricate the external surface of the tip with petroleum jelly grease.

MSS Mana GT ABS

Engine

ENG - 213

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands