manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 274

ALWAYS REPLACE BOTH BEARINGS.
ALWAYS REPLACE THE BEARINGS WITH OTHERS OF THE SAME TYPE.

GASKETS

•

Check that the gaskets are in good conditions; replace them if they show signs of damage

or excessive wear.

ALWAYS REPLACE BOTH GASKETS.
ALWAYS REPLACE THE GASKETS WITH OTHERS OF THE SAME TYPE.

WHEEL AXLE

•

Use a dial gauge to check the wheel

axle eccentricity. Replace the wheel

axle if the eccentricity exceeds the limit

value.

Characteristic

Maximum eccentricity:

0.25 mm (0.0098 in)

•

Using a dial gauge, check that the ra-

dial (A) and the axial (B) eccentricities

of the rim do not exceed the limit value.

An excessive eccentricity is usually

caused by worn or damaged bearings.

Replace the rim if, after replacing the

bearings, the value is not within the

specified limit.

Characteristic

Maximum radial and axial eccentricity:

2 mm (0.0079 in)

Suspensions

MSS Mana GT ABS

SUSP - 274

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands