manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 139

of the red cable and the black cable between the electrical motor connector and the control

unit connector: if they are not OK, restore the cable harness; if they are OK, check that there

is not continuity on the circuit of the electrical motor and replace it.

•

If input current is excessive: check the driving half-pulley movement system mechanically

(excessive friction material).

•

If the signal is not valid: set the key to key ON and check the voltage value at PIN A8 and

B8 which should be approximately 3 V at both PINS; if there is voltage similar to battery

voltage or there is continuity with the ground in one of the two PINS, restore the cable har-

ness; otherwise, replace the transmission ECU.

Connectors

ECU

INJECTION ECU PIN OUT

BROWN "A" CONNECTOR

1. -

2. -

3. Throttle position sensor input

4. -

5. -

6. -

7. -

8. -

9. Idle motor D

10.Front coil control output

11.-

12.-

13.-

14.Air temperature sensor input

MSS Mana GT ABS

Electrical system

ELE SYS - 139

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands