manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 137

the electrical motor and set the position of the driving half-pulley. Phase 1: check continuity

of the red cable and the black cable between the electrical motor connector and the control

unit connector: if they are not OK, restore the cable harness; if they are OK, check that there

is not continuity on the circuit of the electrical motor and replace it.

•

If input current is excessive: check the driving half-pulley movement system mechanically

(excessive friction material).

•

If the signal is not valid: set the key to key ON and check the voltage value at PIN A8 and

B8 which should be approximately 3 V at both PINS; if there is voltage similar to battery

voltage or there is continuity with the ground in one of the two PINS, restore the cable har-

ness; otherwise, replace the transmission ECU.

Drive belt replacement due to wear

•

Check through the diagnosis instrument for any errors in the transmission ECU from the

"errors display" menu. Erase them if necessary.

•

Take the measurement of the gearshift stroke to identify the category to which it belongs.

NOTE

THIS PROCEDURE IS VALID EVEN IN THE EVENT OF REMOVAL AND/OR REPLACEMENT OF
COMPONENTS OF THE VARIATOR UNIT.

•

Replace the transmission belt.

•

Perform the potentiometer reset operations from the "Settings" menu of the diagnosis in-

strument. Delete any errors.

•

Perform the gearshift stroke category operations from the "settings" menu of the diagnosis

instrument.

CAUTION

AFTER ENTERING THE GEARSHIFT STROKE CATEGORY FROM THE "SETTINGS" MENU OF
THE DIAGNOSIS INSTRUMENT, YOU MUST PERFORM A KEY OFF/ON TO STORE THE DATA
ON THE CONTROL UNIT.

•

Check that the gearshift stroke category has been stored correctly from the "parameters"

menu of the diagnosis instrument.

•

Perform the belt replacement operation from the "parameters" menu of the diagnosis in-

strument.

•

To determine the gearshift class category, see the procedure in chapter "Motor - Automatic

transmission - Driving pulley fitting"

See also

Refitting the driving pulley

DRIVING PULLEY CONTROL ELECTRICAL MOTOR

Function

MSS Mana GT ABS

Electrical system

ELE SYS - 137

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands