manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 332

Characteristic

Value/example

Unit of

measure

ment

Notes

hicle identification line - Pins 2-15 of ABS control

unit)

Control unit F000

Possible control unit fault

CAUTION

IN CASE OF SPORADIC FLASHING OF THE ABS WARNING LIGHT (Dorsoduro 750 ABS, SL 750
Shiver ABS) OR WARNING LIGHT+ABS ICON (NA 850 Mana ABS) (ALSO FLICKERING) AND
STORED OR CURRENT ERROR MISSING INDICATIONS, ALL THIS MEANS THAT THERE IS A
BAD CONTACT BETWEEN THE BATTERY POSITIVE LEAD AND PIN 18 OF THE ABS CONTROL
UNIT. CHECK THE TERMINALS, THAT THE 20A FUSE PINS ARE NOT RUSTED AND THE CON-
TINUITY OF THE RED-ORANGE/RED CABLE BETWEEN PIN 18 OF THE ABS CONTROL UNIT
CONNECTOR AND THE BATTERY POSITIVE POLE.

Adjustable parameters screen page

ADJUSTABLE PARAMETERS

Characteristic

Value/example

Unit of

measure

ment

Notes

Coding (1)

Used for re-coding the control unit or coding a new

one.

Coding (2)

Vehicle identification is done according to the con-

nection of PINS 2 and 15 of the ABS control unit

connector and is stored in the control unit memory.

Coding (3)

The identification can be read in the ISO diagram

in the line: Vehicle code.

NOTE: the "X" in the table identifies the connector pin is grounded.

CAUTION

A PASSWORD IS REQUIRED.
TO OBTAIN ONE, CONTACT THE TECHNICAL SERVICE.

Braking system

MSS Mana GT ABS

BRAK SYS - 332

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands