manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 88

The hydraulic pump, the solenoid valves and the sensors are activated by a 20A main fuse.

Control unit

MARELLI CONTROL UNIT

Function

It manages injection/ignition, the system safety

checks and the self-diagnosis function.

Location:

•

Right side, under helmet compartment.

Pin-out:

 see the CONNECTORS section

THE CONNECTION DIAGRAMS ARE IN THE ELECTRICAL SYSTEM SECTIONS; PAY ATTENTION

TO THESE DIAGRAMS AS THEY SHOW THE CONNECTOR/COMPONENT AS VIEWED FROM

THE CABLE HARNESS SIDE, THAT IS LOOKING AT THE CABLES WHEN GOING OUT OF THE

"MAIN" CABLE HARNESS AND INTO THE CONNECTOR/COMPONENT.

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

NAVIGATOR: FUEL INJECTION SYSTEM

PARAMETERS

Target idle rpm

STATUSES

Engine status

Example value:

ON/run/power-latch/stopped.

Immobilizer signal

Example value:

 yes/no

Indicates whether the control unit has received the consent by the instrument panel regarding the im-

mobilizer: coded key or user code entered manually. Potential errors will be shown on the Instrument

Panel Errors screen page, on the DIAGNOSIS section of the instrument panel.

Ignition

Example value:

 Enabled/Disabled

Indicates whether the control unit will enable start-up when requested: in case the safety measures are

not respected, for example the fall sensor is inverted or if the immobilizer does not send the start-up

consent to the control unit, the status is DISABLED.

ACTIVATIONS

Error clearing

ELECTRICAL ERRORS

Electrical system

MSS Mana GT ABS

ELE SYS - 88

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands