manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 138

By means of a transmission gear, it allows the rotation of the driving pulley control bushing which in

turn moves the driving half-pulley axially.

Operation / Operating principle

DC motor with pulse activation (duty cycle). The rotation in both directions is controlled by the control

unit by inverting the power supply polarity.

Level in wiring diagram:

Transmission management

Location:

•

on the vehicle: up and to the left of the transmission cover

•

connector: Under helmet compartment

Electrical specifications:

•

Winding resistance < 1 Ohm

•

Input: nominal 10A

•

Maximum input: 22 A

Pin-out:

1. Red

2. Black

AXONE / AUTOMATIC TRANSMISSION system

PARAMETERS

Driving pulley control electrical motor duty cycle

Example value: %

It is a speed indicator of the driving half-pulley movement in axial direction.

NOTE:

 When troubleshooting, use the interface, code 020481Y, with the adaptor, code 020481Y004.

The correspondence between the control unit PIN and the interface PIN is the following: control unit

PIN A1….A8 and interface PIN interface 11….18, control unit PIN B1….B8 and interface PIN interface

21….28, control unit PIN C1….C8 and interface PIN interface 31….38.

ERRORS

Driving pulley electrical motor - Code 900A

 - excessive actuation time/ excessive current input/ signal

not valid.

Error cause

•

If activation time is excessive: the position is not reached within a standard time although

the driving pulley motion control is activated. If input current is excessive: the transmission

ECU detects excessive ampere input for the driving pulley electric motor. If the signal is not

valid: a short-circuit to ground has been detected at battery PIN A8 or PIN B8.

Troubleshooting

•

If activation time is excessive: check circuit continuity between PIN A8 and B8: if it is not

OK, continue with Phase 1; if it is OK, check the gears which receive the movement from

the electrical motor and set the position of the driving half-pulley. Phase 1: check continuity

Electrical system

MSS Mana GT ABS

ELE SYS - 138

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands