manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 82

Diagnosis

An access code is required to enter this menu which controls the diagnosis function:

•

ENTER SERVICE CODE

This is a 5-digit code, fixed for each vehicle. For these vehicles, the code is:

12321

If the code is incorrect, the following message is displayed:

•

INCORRECT CODE

and the instrument panel goes back to the main menu. Otherwise, the following menu is displayed:

•

EXIT

•

ECU DIAGNOSIS

•

INSTRUMENT PANEL ERRORS

•

ERROR CLEARING

•

VEHICLE SERVICING RESET

•

UPDATE

•

CHANGE KEYS

•

KM / MILES

ECU diagnosis

In this mode a chart is displayed showing potential

errors in the control unit.

IT IS NECESSARY TO REFER TO THE ERROR

INDICATIONS GIVEN BY NAVIGATOR FOR

THIS VEHICLE.

The instrument panel does not keep all previous errors stored in its memory.

INSTRUMENT PANEL ERRORS

In this mode, a chart is displayed showing potential

errors in the immobilizer and the sensors connec-

ted to it.

INSTRUMENT PANEL errors

In this mode, a chart is displayed showing potential errors in the immobilizer and the sensors connected

to it.

DSB 01

 - Immobilizer fault: key code read but not recognised.

Electrical system

MSS Mana GT ABS

ELE SYS - 82

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands