manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 259

Refitting the transmission cover

- Follow the removal steps but in reverse order,

using the specific tool and being careful to tighten

to the prescribed torques.

Locking torques (N*m)

Driven pulley nut

 

153 - 187

 

Internal transmission

cover screws

 

11 - 13

 

External transmission cov-

er screws

 

5 - 7

- For vehicles with chassis included in the following range

ZD4RC000_7S000002 - ZD4RC000_8S000737

,

after fitting the cover, fit the driving pulley position sensor until it stops, on a 1-mm (0.039 in) thickness

gauge placed between the lever and cover, making sure that the first gear is engaged (corresponding

to the sensor lever placed facing out).

- Once the sensor is installed, make sure that the distance of the lever to the cover is between (0.7 - 1)

mm (0.027 - 0.039 in).

For vehicles with chassis included in the range indicated above, just fit the sensor by tightening

the two screws.

EACH TIME THE ROTATING POSITION SENSOR OR ANY COMPONENT OF THE TRANSMISSION
IS REMOVED OR REPLACED, CARRY OUT THE "POTENTIOMETER RESET" OPERATION AS
INDICATED IN THE WORKSHOP MANUAL, "ELECTRICAL SYSTEM/DRIVING PULLEY POSITION
SENSOR" CHAPTER. UPON RESETTING, MAKE SURE THAT THE POSITION SENSOR LEVER
ROTATES FREELY AND DOES NOT TOUCH THE COVER. THIS RESETTING OPERATION IS
CARRIED OUT BEFORE THE FIRST START-UP.

MSS Mana GT ABS

Engine

ENG - 259

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands