manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 256

- Grease the control bushing with suitable grease,

as shown in figure.

- Screw the control bushing to the complete mov-

able driving half-pulley. Push the bushing and

check that the bushing sliding axis and the slider

support engage by means of the two teeth.

- Once the gear checking is finished, unscrew the

driving pulley 1/2 of a turn.

CAUTION

MAKE SURE THERE IS A CORRECT GEAR BETWEEN THE
TOOTHED BUSHING AND THE SLIDER SUPPORT.

CAUTION

NO OTHER ELEMENT OF THE TRANSMISSION MUST BE
GREASED.

- Preassemble the belt on the rear pulley with a special tool.

Specific tooling

020659Y

 

Tool to remove clutch and repl. belt

- Fit the unit following the removal steps but in reverse order with the specific tool being careful to tighten

to the prescribed torques.

Engine

MSS Mana GT ABS

ENG - 256

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands