manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 175

Flywheel components check

- Check that the magnets are in good conditions.

- Check that the magnet support cage is not de-

formed or broken.

Checking the starter clutch

- Make sure the freewheel faying surfaces are in good condition.

- Thoroughly clean the freewheel to remove any LOCTITE left.

- Degrease the threading of the freewheel holes and the fixing screws.

- Apply the recommended product to the end of the screws.

Recommended products

Loctite 243

 

Medium strength threadlock

-

- Fit the freewheel on the magneto flywheel, mak-

ing sure that the ground side is in contact with the

flywheel, that is the wheel seeger ring should be

visible.

- Tighten the 6 fixing screws in a criss-cross se-

quence to the prescribed torque.

- Lubricate the freewheel «rollers».

MSS Mana GT ABS

Engine

ENG - 175

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands