APRILIA MSS Mana GT ABS Service Station Manual Download Page 328

Page: 328 / 394

7. CONTACT TECHNICAL SERVICE

8. PERFORM THESE CHECKS:

•

A. Cable continuity between PIN 8 of the ABS control unit connector and PIN 28 of the

instrument panel.

•

B. Check connectors - refer to the operations described in the chapter

If the previous checks are OK, the causes might be:

•

C. ABS control unit malfunction

•

D. Instrument panel malfunction

NOTE: to check the wheel speed sensor through AXONE, refer to the operations described in

chapter "ELECTRIC SYSTEM/CHECKS AND CONTROLS/SPEED SENSOR".

Using axone for the abs

Abs screen pages

ISO screen page

ISO

This screen page shows general data regarding

the control unit, for example software type, map-

ping, control unit programming date

ISO SCREEN PAGE

Characteristic

Value/example

Unit of

measure

ment

Notes

Vehicle manufacturing date
Frame number
Software version
Vehicle code

Mana/Shiver/Dorso-

duro/Scarabeo

The vehicle code stored in the control unit is read.

Vehicle identification according to
the status of Pin 2 and 15 of the ABS
control unit connector

Mana/Shiver/Dorso-

duro/Scarabeo

The vehicle type (Mana/Shiver/Dorsoduro) is de-

fined according to the connection found for PIN 2
and PIN 15 of the ABS control unit connector. see

table on workshop booklet

Braking system

MSS Mana GT ABS

BRAK SYS - 328

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Search results

Summary of Contents for MSS Mana GT ABS

Reviews:

Brands by name

Popular brands

APRILIA MSS Mana GT ABS, Service Station Manual

Search results

Summary of Contents for MSS Mana GT ABS

Reviews:

Brands by name

Popular brands