APRILIA MSS Mana GT ABS Service Station Manual Download Page 79

Page: 79 / 394

Given this, and for some kinds of problems, the

engine can be started only if the side stand is up.

If there is an immobilizer failure at ignition, the instrument panel requests you to enter a user code. If

the code is entered correctly, the instrument panel signals the failure by displaying the SERVICE icon

and the red general warning light comes on.

Air temperature sensor failure

In case of air temperature sensor failure, the in-

strument panel signals the problem by displaying

the "--" symbol steadily at the position where the

temperature value is generally displayed. In this

case the red general warning light does not turn

on.

Oil failure

In case of failing oil pressure or oil pressure sensor

failure, the bulb and the red general warning light

turn on the instrument panel.

Engine overheating alarm

The engine overheating alarm is activated when the temperature is higher than or equal to 110 °C (230

°F). The red general warning light turns on and the thermometer icon flashes on the display to signal

this condition.

Electronic control unit disconnected alarm

In case no connection is detected, the disconnec-

tion icon is displayed on the instrument panel and

the red general warning light turns on to signal this

condition.

MSS Mana GT ABS

Electrical system

ELE SYS - 79

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Search results

Summary of Contents for MSS Mana GT ABS

Reviews:

Brands by name

Popular brands

APRILIA MSS Mana GT ABS, Service Station Manual

Search results

Summary of Contents for MSS Mana GT ABS

Reviews:

Brands by name

Popular brands