manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 116

Transmission control unit

Function

It controls the TRANSMISSION system.

Operation / Operating principle

It receives information from the sensors connected to it and, via CAN line communication with the

instrument panel and the injection control unit, it controls the predetermined operating strategies for the

position of the driving pulley in order to obtain the gear ratio requested by the user (manual transmission)

or expected according to the kind of calibration of the selected gear (automatic transmission).

Level in wiring diagram:

 transmission management

Position:

•

on the vehicle: between the helmet compartment and the saddle

•

connector (if available): on the control unit

Electrical specifications: -

Pin-out:

 see the CONNECTORS section

CAUTION

BEFORE CARRYING OUT ANY TROUBLESHOOTING, CAREFULLY READ THE GENERAL TROU-
BLESHOOTING CONCEPTS FOR ELECTRICAL DEVICES AT THE BEGINNING OF THE CHECK
AND CONTROL SECTION IN THE ELECTRICAL SYSTEM CHAPTER.

AXONE / AUTOMATIC TRANSMISSION system

ISO SCREEN PAGE

Hardware number -

 Example value: 04

Hardware version number -

 Example value:0004

Software number -

 Example value:04

Software release number -

 Example value:0033

NOTES -

 Control unit mapping

PARAMETERS

Automatic system

Temperature inside the control unit

Example value:

 °C

There is a sensor inside the control unit.

Maximum value reached by the temperature inside the control unit

Electrical system

MSS Mana GT ABS

ELE SYS - 116

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands