manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 302

Specific tooling

AP8140150

 

Perforated rod for piston air bleed

•

Fit the special tool.

Specific tooling

020888Y

 

Pliers for pre-fill pipe

•

With the aid of a second operator, hold

the pumping member rod firmly, lower

the spacer retention tool, insert the

stop ring and the plate separating the

spacer-pumping member between the

ring and the nut.

Specific tooling

AP8140148

 

Spacer-piston separating plate

•

Tighten completely the nut on the

pumping member pin rod.

•

Insert the sleeve cap on the pumping

member pin rod and tighten it.

•

Tighten the nut, on the cover to the

specified torque.

•

Tighten the sleeve cap, to the prescri-

bed tightening torque.

NOTE

Suspensions

MSS Mana GT ABS

SUSP - 302

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands