manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 300

•

Fill the sleeve with the adequate quality and type of oil indicated on the recommended prod-

ucts table.

Characteristic

Fork oil quantity (left stem) (Marzocchi)

505 cc (30.82 cu in)

•

Unscrew the plug manually until the

stop.

•

Insert a spanner on the nut under the

plug the cover allowing to tighten the

plug to the tightening torque.

•

Tighten the sleeve cap, to the prescri-

bed tightening torque.

NOTE

THE FOLLOWING OPERATIONS REFER TO THE SACHS FORKS.

NOTE

THE OPERATIONS DESCRIBED BELOW ARE VALID FOR BOTH STEMS.

•

Place the stanchion on a work table in upright position.

•

Fill the sleeve with the adequate quality and type of oil indicated on the recommended prod-

ucts table.

Suspensions

MSS Mana GT ABS

SUSP - 300

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands