manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 303

THE OPERATIONS DESCRIBED BELOW ARE VALID FOR BOTH STEMS.

•

Place the stanchion on a work table in upright position.

•

Fill the sleeve with the adequate quality and type of oil indicated on the recommended prod-

ucts table.

WARNING

MOVE THE PUMPING ELEMENT SEVERAL TIMES UNTIL
AIR BUBBLES ARE SEEN ON THE OIL SURFACE.

THE SLEEVE MUST BE PERFECTLY UPRIGHT IN ORDER
TO MEASURE THE CORRECT OIL LEVEL. THE OIL LEVEL
MUST BE THE SAME IN BOTH STANCHIONS.

Characteristic

Fork oil quantity (for each stem):

535 cm³ (32.65 cu.in)

Oil level (from sleeve rim, without the spring
and with pumping member fully down)

122 mm (4.80 in).

•

Fit the preloading pipe together with

the spring centring.

•

Fit the special tool.

Specific tooling

AP8140147

 

Spacer tool

MSS Mana GT ABS

Suspensions

SUSP - 303

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands