manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 120

AFTER ENTERING THE GEARSHIFT STROKE CATEGORY FROM THE "SETTINGS" MENU OF
THE DIAGNOSIS INSTRUMENT, YOU MUST PERFORM A KEY OFF/ON TO STORE THE DATA
ON THE CONTROL UNIT.

•

Check that the gearshift stroke category has been stored correctly from the "parameters"

menu of the diagnosis instrument.

•

Perform the belt replacement operation from the "parameters" menu of the diagnosis in-

strument.

•

To determine the gearshift class category, see the procedure in chapter "Motor - Automatic

transmission - Driving pulley fitting"

See also

Refitting the driving pulley

Driving pulley position sensor

SENSOR FITTING

Reset procedure

It is necessary to use Axone in case the variator unit is removed and the potentiometer is replaced or

removed: Potentiometer reset

CAUTION

FOR VEHICLES INCLUDED IN THE FOLLOWING RANGE
ZD4RC000_7S000002 - ZD4RC000_7S000737
IN ORDER TO FIT THE DRIVING PULLEY POSITION SENSOR CORRECTLY, SEE THE "Engine"
CHAPTER, "Transmission Cover Fitting" SECTION.

See also

Refitting the

transmission cover

Function

It tells the position of the driving half-pulley to the

transmission ECU.

Operation / Operating principle

It is a double track potentiometer, with inversely

proportional voltage variation.

Level in wiring diagram:

transmission manage-

ment

Location:

•

on the vehicle: on the upper part of the

transmission cover.

•

connector: directly on the sensor.

Electrical characteristics:

Electrical system

MSS Mana GT ABS

ELE SYS - 120

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands