APRILIA MSS Mana GT ABS Service Station Manual Download Page 193

Page: 193 / 394

IF THE CHAIN HAS DAMAGED THE PINION, REPLACE THE CRANKSHAFT.

Checking the sliders

- Check that the guide slider and the tensioner pad

are not excessively worn.

- Replace the sliders if they are worn.

Cam timing

The ignition advance is determined electronically on the basis of parameters known by the control unit.

For this reason it is not possible to state the reference values based on the engine revs.

The ignition advance value can be measured at any time with the Axone.

It is possible to check whether the ignition advance determined by the injection system does in fact

correspond with the value actually activated on the engine, by means of the stroboscopic light.

Specific tooling

AP8140595

Axone + battery charger (230V 50Hz)

AP8202311

Axone + battery charger (110V 60Hz)

020330Y

Stroboscopic light for timing checking

- Unscrew the TDC reference inspection cap.

- Connect the stroboscopic light.

- Connect the Axone.

- Start the engine.

- Select the «parameter» function from the menu.

- Select the stroboscopic light control in the traditional four-stroke engine position (1 spark, 2 revs).

- Check that the real values of revs and ignition advance match those measured using the Axone.

- Refit the inspection cap on the flywheel side.

Specific tooling

MSS Mana GT ABS

Engine

ENG - 193

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Search results

Summary of Contents for MSS Mana GT ABS

Reviews:

Brands by name

Popular brands

APRILIA MSS Mana GT ABS, Service Station Manual

Search results

Summary of Contents for MSS Mana GT ABS

Reviews:

Brands by name

Popular brands