manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 147

•

The transmission ECU cannot send CAN signals; it receives signals from the instrument

panel and the injection control unit: the control unit may need replacing.

Troubleshooting

•

Replace transmission ECU.

CAN line to instrument panel Code 9007

 - no signal

Error cause

•

No signal arrives to the instrument panel from either CAN line cables.

Troubleshooting

•

Check the connector of the instrument panel: if it is not OK, restore; if it is OK, check the

continuity of the two lines from the instrument panel connector to the transmission ECU

connector: if not OK, restore the cable harness; if OK, replace the instrument panel.

CAN line to injection ECU Code 9006

 - no signal

Error cause

•

No signal arrives from the injection ECU from either CAN line cables.

Troubleshooting

•

Check the transmission ECU connector and the Marelli control unit connector: if they are

not OK, restore; if they are OK, check the continuity of the two lines from the transmission

ECU connector and from the Marelli control unit connector: if it is not OK, restore the cable

harness; if it is OK, replace the Marelli control unit.

AXONE / FUEL INJECTION system:

ERRORS

Mute Node CAN Line, U1601 -

 Mute Node

Error cause

•

The control unit cannot send CAN signals; it receives signals from the instrument panel and

the transmission ECU: the control unit may need replacing.

Troubleshooting

•

Replace injection ECU.

CAN line, no signal, U1602-

 Bus Off

Error cause

•

No communication on CAN line (PIN B4 and/or PIN B5): problem on the whole network (for

example, battery cut-off or short circuited or shorted to ground).

Troubleshooting

•

Check the Marelli control unit connector: if not OK, restore; if OK, check the earth insulation

of the two CAN lines from PIN 20 and PIN 51 of the VEHICLE connector: If not OK, restore

the cable harness; if OK, check continuity of the two CAN lines from the Marelli control unit

VEHICLE connector to the filter casing large connector and to the instrument panel con-

MSS Mana GT ABS

Electrical system

ELE SYS - 147

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands