manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 184

MINIMUM DIAMETER ALLOWED

Specification

Desc./Quantity

Bearing A Ø:

41.910 mm

Bearing B Ø:

19.940 mm

- Using a gauge, measure the height of the cams.

LIMITS ALLOWED

Specification

Desc./Quantity

Inlet:

33.740 mm

Outlet:

33.170 mm

Standard axial clearance:

0 ÷ 0.22 mm

Maximum axial clearance allowed:

0.3 mm

STANDARD HEIGHT

Specification

Desc./Quantity

Inlet:

33.988 mm

Outlet:

33.417 mm

- Check there are no signs of wear on the contact pads with the cam and on the articulated plate of the

set screws.

- In case of wear, replace the component.

- Check there are no signs of wear or scoring on the rocking lever pins.

Characteristic

Standard diameter:

Ø 13 - 0.010 -0.018 mm

See also

Assembly clearances

Engine

MSS Mana GT ABS

ENG - 184

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands