manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 258

•

Turn over the complete movable driv-

ing half-pulley and insert the spacer

until it stops.

•

Using a depth gauge, measure the pro-

trusion of the spacer with respect to the

upper edge of the movable driving half-

pulley.

CAUTION

ONCE MEASURED, UNDO THE ADVANCEMENT BUSHING
BY ABOUT HALF A TURN.

CLASSES CONVERSION TABLE

Specification

Desc./Quantity

CLASS

CHECK POSITION VALUE (mm)

1

21.82 - 21.94

2

21.95 - 22.04

3

22.05 - 22.14

4

22.15 - 22.24

5

22.25 - 22.34

6

22.35 - 22.44

7

22.45 - 22.54

8

22.55 - 22.68

Engine

MSS Mana GT ABS

ENG - 258

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands