manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 24

Name

Description

Dimensions

Initials

Quantity

Connecting rod

22 -0.10 -0.15

C

D = 0.20 ÷ 0.60

Complete crankshaft

104 +0.1 -0.05

E

Characteristic

Crankshaft-crankcase axial clearance (H)

0.1 ÷ 0.45 mm (when cold)

- Measure the inside diameter of the connecting

rod small end using a bore meter.

NOTE

IF THE CONNECTING ROD SMALL END DIAMETER EX-
CEEDS THE STANDARD DIAMETER, SHOWS SIGNS OF
WEAR OR OVERHEATING, REPLACE THE CRANKSHAFT
AS DESCRIBED IN THE «CRANKCASE AND CRANK-
SHAFT» CHAPTER.

Characteristic

Standard diameter:

22 + 0.025 +0.015 mm

Depending on the type of crankshaft/crankcase coupling, the following types of bushings listed in the

table should be used.

Characteristics

MSS Mana GT ABS

CHAR - 24

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands