APRILIA MSS Mana GT ABS Service Station Manual Download Page 234

Page: 234 / 394

- Fit the oil scavenge pump and the bulkhead of

the oil anti-backflow plate.

- Tighten the two screws indicated to the prescri-

bed torque.

Locking torques (N*m)

Screws fixing oil pump to crankcase

5 - 6

- Fit the water pump control gear on the oil pump

shaft.

- Tighten the locking screw with the washer and

tighten to the prescribed torque.

Locking torques (N*m)

Water pump gear fixing screws

5 - 6

- Once the oil scavenge pump fitting is finished,

operate from outside the flywheel side crankcase

half.

- Make sure the gasket is in the correct position.

NOTE

THE TOOTH OF THE GASKET MUST BE IN ITS SEAT.

- Fit the timing chain and the timing chain tensioner

slider.

- Tighten the fixing screw to the prescribed torque.

Locking torques (N*m)

Tensioner slider fixing screw

10 - 14

- Fit the oil pressure pump.

Engine

MSS Mana GT ABS

ENG - 234

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Search results

Summary of Contents for MSS Mana GT ABS

Reviews:

Brands by name

Popular brands

APRILIA MSS Mana GT ABS, Service Station Manual

Search results

Summary of Contents for MSS Mana GT ABS

Reviews:

Brands by name

Popular brands