APRILIA MSS Mana GT ABS Service Station Manual Download Page 368

Page: 368 / 394

Rider footrest plate

The following operations also apply to both foot-

rest holder plates.

•

Undo and remove the lower fixing

screw and collect the washer.

CAUTION

UPON REFITTING, THE LOWER M10 FIXING SCREW
SHOULD BE TIGHTENED TO THE SPECIFIED LOCKING
TORQUE.

Locking torques (N*m)

Lower screw fixing rider footrest

25 Nm (18.44 lbf

ft)

•

Undo and remove the central fixing

screw and collect the washer.

The following operations are only applicable to re-

move the left footrest holder plate.

•

Unscrew and remove the rear fixing nut

and collect the washer.

•

Remove the passenger footrest sup-

port.

Bodywork

MSS Mana GT ABS

BODYW - 368

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Search results

Summary of Contents for MSS Mana GT ABS

Reviews:

Brands by name

Popular brands

APRILIA MSS Mana GT ABS, Service Station Manual

Search results

Summary of Contents for MSS Mana GT ABS

Reviews:

Brands by name

Popular brands