APRILIA MSS Mana GT ABS Service Station Manual Download Page 80

Page: 80 / 394

Turn indicator malfunction

When the instrument panel detects a failing turn

indicator, the turn indicator warning light flashes

twice as fast and the problem is signalled on the

digital display.

Alarms - transmission

In case of alarms for gearshift controls and mode

control connected to the transmission control unit,

three kinds of symbols are shown on the display,

according to the nature of the alarm: F, H and M.

F stands for "foot" (foot pedal), H stands for "han-

dlebar" (handlebar control) and M is for

"mode" (gear mode selection).

In case of alarms related to the transmission con-

trol unit, the general alarm warning light is lit and

the display shows the word GEAR.

CAUTION

IN CASE THE HANDLEBAR CONTROLS ARE DISABLED,
THE H SYMBOL WILL BE ALSO SHOWN ON THE DIGITAL
DISPLAY.

Electrical system

MSS Mana GT ABS

ELE SYS - 80

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Search results

Summary of Contents for MSS Mana GT ABS

Reviews:

Brands by name

Popular brands

APRILIA MSS Mana GT ABS, Service Station Manual

Search results

Summary of Contents for MSS Mana GT ABS

Reviews:

Brands by name

Popular brands