manualshive.com logo in svg

APRILIA MSS Mana GT ABS, Service Station Manual

Share
Download
APRILIA MSS Mana GT ABS Service Station Manual Download Page 146

•

If the initial position of the connector

and the driving lever is not that shown

in fig. 1, the connector will not be prop-

erly coupled and the distance meas-

ured will be greater (12 mm approx.

(0.47 in)). In this case repeat the oper-

ation as described in the two previous

points.

IT IS ADVISABLE TO CREATE A TEMPLATE

TO CHECK THE CORRECT CONNECTOR IN-

SERTION.

•

Insert the housing as shown in the fig-

ure.

Can line

CAN line

Function

It allows communication between the Marelli injection control unit, the transmission ECU and the in-

strument panel.

Level in wiring diagram:

CAN line

Pin-out:

 see wiring diagram

AXONE / AUTOMATIC TRANSMISSION system:

ERRORS

"Mute Node" CAN Line, U1601

 - Mute Node.

Error cause

Electrical system

MSS Mana GT ABS

ELE SYS - 146

Summary of Contents for MSS Mana GT ABS











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands