Altigen AltiWare OE 4.6 Administration Manual Download | Manualshive

Page: 21 / 518

background image

AltiWare OE System Installation & Administration Manual

xxiii

Lia

b

ilit
iy
&
W
a

rra
nt
y

•

Vermeiden Sie das Berühren von nichtisolierten Telefonkabeln oder Terminals, wenn
die Telefonleitung an den Netzschnittstellen nicht abgeschaltet ist.

UL Regulatory Safety Requirements

(Requisitos Reglamentarios de Seguridad de La Asociación de
Aseguradores (UL)/Sicherheitserfordernisse gemäß UL
(Underwriter's Laboratories, Inc.))

Host Computer

1.

Model AltiGen/AltiServ apparatus is approved for connection to Telecommunications
Systems specified in these instructions for use subject to the conditions set out in them.
Any other usage will INVALIDATE this approval.

2.

The host machine shall be “CE” marked, with the internal ISA and PCI slots operating
at SELV in accordance with EN60950, 1992, issue 2, +A4.

3.

This apparatus MUST be professionally installed.

4.

The host machine MUST be hardwired earthed in accordance with EN60950, 1992,
issue 2, +A4, 1997, cl. 6.2.1.2 with an earth wire from the host machine earthing
terminal to the building earth.

5.

The host machine SELV circuit is connected to the protective earthing terminal in
accordance with EN60950 cl. 2.5.

6.

The host machine ISA bus pins B1, B10, or B31 (edge connectors on CPU mother-
board/backplane) MUST be less than 0.1 Ohms to host machine earthing terminal.

7.

AltiGen complies with PCI Board specifications Rev. 2.1 (5V 32-bit).

8.

The power required by the host machine and the total of all adapter cards installed within
the host environment, together with any ancillary apparatus, shall not exceed the power
specification of the host machine.

9.

It is essential that, when other option cards are introduced that use or generate a
hazardous voltage, the minimum creepages and clearances specified in the following
table are maintained. A hazardous voltage is one that exceeds 42.4V peak AC or 60V
DC. If you have any doubt, seek advice from a competent engineer before installing
other adapters into the host machine.

Clearance (mm)

Creepage (mm)

Voltage used or generated by

host or other cards

2.0

2.4 (3.8)

Up to 50 Vrms or Vdc

ISA bus

ISA bus

B1

B10

B31

«
...
19
20
21
22
23
...
»

Summary of Contents for AltiWare OE 4.6







































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltiWare OE 4.6

Brand: Navman Pages: 10

FLASH MEDIA SERVER 2-INSTALLING FLASH MEDIA SERVER...

Brand: MACROMEDIA Pages: 16

NG Network Access Client SP4

Brand: Barracuda Networks Pages: 10

Brand: AMX Pages: 12

Brand: Xerox Pages: 52

Brand: FARONICS Pages: 34

Brand: Ulead Pages: 58

Brand: AMX Pages: 24

Brand: Pantone Pages: 12

IDENTITY MANAGER 3.6.1 - STAGING BEST PRACTICES GUIDE 2010

Brand: Novell Pages: 54

DSN-210-SW - SureSync Continuous Data...

Brand: D-Link Pages: 4

ACTIVE NETWORK ABSTRACTION 3.7.2

Brand: Cisco Pages: 2

Brand: Cabletron Systems Pages: 495

Brand: Asus Pages: 3

GigaX 1024P User's

Brand: Asus Pages: 8

Brand: Asus Pages: 90

Brand: Adobe Pages: 6

Brand: Adobe Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands