Altigen AltiWare OE 4.6 Administration Manual Download

Page: 480 / 518

B-6

AltiWare OE System Installation & Administration Manual

Ecuador MFC-R2

Set calling part category: 1

[Assume no caller ID provided]:

Incoming sequence: DID/DNIS

In-call signaling (depend on how many DID digits):

For 3-digit DID, set to (113)6

For 4-digit DID, set to (1113)6

For 5-digit DID, set to (11113)6

For 6-digit DID, set to (111113)6

For 7-digit DID, set to (1111113)6

For 8-digit DID, set to (11111113)6

[Assume caller ID provided] :

Incoming sequence (same as above shown):

DID/DNIS * Caller ID

In-call signaling (depend on how many DID digits):

For 3-digit DID, set to (115)*(K)36

For 4-digit DID, set to (1115)*(K)36

For 5-digit DID, set to (11115)*(K)36

For 6-digit DID, set to (111115)*(K)36
For 7-digit DID, set to (1111115)*(K)36
For 8-digit DID, set to (11111115)*(K)36

Ecuador MFC-LME

Set calling part category: 2

[The switch doesn't support caller ID transmission]:

Incoming sequence: DID/DNIS

In-call signaling (depend on how many DID digits):

For 3-digit DID, set to (113)1

For 4-digit DID, set to (1113)1

For 5-digit DID, set to (11113)1

For 6-digit DID, set to (111113)1

For 7-digit DID, set to (1111113)1
For 8-digit DID, set to (11111113)1

Korea MFC-R2

Set calling part category: 1

[The switch doesn't support caller ID transmission]:

Incoming sequence: DID/DNIS

In-call signaling (depend on how many DID digits):

For 3-digit DID, set to (113)6

For 4-digit DID, set to (1113)6

For 5-digit DID, set to (11113)6

For 6-digit DID, set to (111113)6

For 7-digit DID, set to (1111113)6
For 8-digit DID, set to (11111113)6

Table 1: Foreign Countries/Signaling Values

Country

Signaling Values

Summary of Contents for AltiWare OE 4.6







































































































































































































































































































































































































































































































































Search results

Summary of Contents for AltiWare OE 4.6

Reviews:

Related manuals for AltiWare OE 4.6

Brands by name

Popular brands

Altigen AltiWare OE 4.6, Administration Manual

Search results

Summary of Contents for AltiWare OE 4.6

Reviews:

Related manuals for AltiWare OE 4.6

Brands by name

Popular brands