Altigen AltiWare OE 4.6 Administration Manual Download | Manualshive

Page: 167 / 518

background image

System Configuration

AltiWare OE System Installation & Administration Manual

5-23

5

.S
y

s

te

m

Confi

g

ur
a

tio

n

To access Messaging setup, select System Configuration... on the
Management menu, then click the Messaging tab.

:

Figure 14.

Messaging window, System Configuration

Setting Message Notification Retries

When a message is sent to a user’s email in-box or voice mailbox and
outcall notification is configured, notification is sent to the user. You can
set the retry setting for the notification as follows:

Parameter

Description

Maximum Retry
Count

Can be between 0 and 16. This is the number of times
the system will try to deliver a voice message
notification after the original attempt. For example, 5
retries means five tries after the original, or 6 total
attempts.

«
...
165
166
167
168
169
...
»

Summary of Contents for AltiWare OE 4.6







































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltiWare OE 4.6

Brand: Canon Pages: 2

Brand: Canon Pages: 153

Brand: Canon Pages: 132

Brand: Canon Pages: 135

Brand: Canon Pages: 198

Brand: Canon Pages: 98

Network Shutdown Module V3

Brand: Eaton Pages: 65

SmartNode Series

Brand: Patton electronics Pages: 655

APPLICATION STACK 1.4 RELEASE

Brand: Red Hat Pages: 22

Web-based Management Utility

Brand: Supermicro Pages: 64

Brand: AMX Pages: 53

25366 - Camera Control Pro

Brand: Nikon Pages: 94

Brand: Native Instruments Pages: 58

Brand: EMC Pages: 106

Brand: AVIRA Pages: 25

FLEXXPECT-LABELLING

Brand: Omron Pages: 2

Brand: Omron Pages: 2

Brand: Omron Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands