Altigen AltiWare OE 4.6 Administration Manual Download Page 59 | Manualshive

Page: 59 / 518

background image

Overview

AltiWare OE System Installation & Administration Manual

1-25

1.
O

v

erv

iew

•

AltiServ-to-AltiServ Networking Capability - multiple AltiServ
systems at the same or remote locations can be linked through an IP
network. Also, this feature provides toll savings on long distance calls
by allowing users to dial a remote AltiServ system via an IP trunk and
then the destination phone number through PSTN.

•

AltiServ Feature Support - many of the AltiServ features are also
available when using IP trunks. See “Voice over IP Session Support
AltiServ Features” on page 1-27.

•

Board ID Support - The board ID of the Triton IP board is displayed
in the AltiAdmin board window. This can be used to relate a Triton
VoIP board to a hardware board.

•

DTMF Remote Carriage - DTMF tones and/or digits are detected and

sent out-of-band, over a reliable TCP/IP channel to the remote
AltiServ, to guarantee the delivery.

•

Dialing Prefix Filter - users may select a PSTN or IP trunk when

making outgoing calls by dialing a configurable access code.

•

Echo Cancellation - due to bandwidth limitations and device loading,

long delays may occur during packet delivery process, which worsens
the echo effect of recorded and live voice speech. Echo cancellation is
provided to maintain reasonable voice quality.

•

G.711 Codec - toll quality (64K) digital voice encoding, which
guarantees interoperability for better voice quality.

•

G.723.1 Codec - a dual rate audio encoding standard, which provides
near toll quality performance under clean channel conditions. VAD
(Voice Activity Detection) capability is also included to suppress
silence packets.

•

H.323 Standard Support - AltiWare IP is based on the H.323
protocol, which is an emerging ITU standard for multimedia
communications over IP.

•

IP Extensions - the IP Extension feature allows an H.323 compliant
terminal device to connect to AltiServ. IP extensions have the same
functionality as an analog station. Group agents can log in from a
remote location using IP extensions.

•

IP Phone Service - a service that runs on the same system as AltiServ,
is installed together with AltiServ, and connects to AltiServ through
enhanced AltiLink Plus protocol on behalf of AltiGen IP Phones.

«
...
57
58
59
60
61
...
»

Summary of Contents for AltiWare OE 4.6







































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AltiWare OE 4.6

Avccam AG-AF100A Series

Brand: Panasonic Pages: 19

GS110TP - ProSafe Gigabit Smart Switch

Brand: NETGEAR Pages: 2

DISK DIRECTOR SUITE 10

Brand: ACRONIS Pages: 127

Brand: Spectrel Pages: 74

EliteBook 8460W

Brand: HP Pages: 41

Elite 7300 Microtower

Brand: HP Pages: 4

MultiSeat ms6000

Brand: HP Pages: 63

EliteBook 8560p

Brand: HP Pages: 4

Elitebook 8560W

Brand: HP Pages: 74

Fabric OS 7.0.0

Brand: HP Pages: 138

Brand: HP Pages: 50

EliteBook 2560p

Brand: HP Pages: 34

Brand: HP Pages: 102

Brand: HP Pages: 16

Evo D300 - Convertible Minitower

Brand: HP Pages: 2

Brand: HP Pages: 66

Elite 7500 Microtower

Brand: HP Pages: 4

Neoware c50 - Thin Client

Brand: HP Pages: 228

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands