manualshive.com logo in svg

Altigen AltiWare OE 4.6, Administration Manual

Share
Download
Altigen AltiWare OE 4.6 Administration Manual Download Page 65

AltiWare OE System Installation & Administration Manual

2-1

2

.

Sy
st

em

Re
quir

e

me

nts

C

H A P T E R

2

System Requirements

Hardware Requirements

AltiServ hardware requirements depend on the number of extensions
(lines) and trunks your site requires. Refer to Table 4 on page 2-12 for
AltiServ platform selection.

System Key Requirement

AltiWare OE 4.6 is integrated with a system key, a hardware security
device that allows the software to run ONLY when that system key is
attached to the parallel or USB port of the server that OE is running on. The
system key is required for initial installation, software upgrade process,
and upon system reboot.

One pre-assigned, DB-25 parallel port system key is included with every
copy of AltiWare OE 4.6 (upgrade or original). Each system key has a
unique key designated for a particular AltiWare software package - system
keys cannot be shared among systems. System keys are also available in
USB form factor. USB system keys must be special ordered.

Selecting the AltiServ Platform 

In order to maintain your AltiServ system integrity and plan for future site
expansion, you should take into consideration the following points before
selecting the AltiServ platform:

• Reliability

• Expandability

• System performance

Minimum System Requirements

The following operating systems are supported in OE 4.6:

• For AltiWare OE 4.6 Server: Microsoft NT 4.0 Server with SP6,

Windows 2000 Server with SP2 and above.

Summary of Contents for AltiWare OE 4.6







































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands