manualshive.com logo in svg

Altigen AltiWare OE 4.6, Administration Manual

Share
Download
Altigen AltiWare OE 4.6 Administration Manual Download Page 211

Board Configuration

AltiWare OE System Installation & Administration Manual

6-29

6.
B

o

a

rd

Confi

g

ur
a

tion

2.

Triton VoIP Board is Not Installed Properly - Refer to the Quick
Installation Guide for more details on proper installation of the Triton
VoIP board.

Configuring the Triton T1/PRI Board

Through AltiAdmin, the Triton T1/PRI board can be configured for either
digital T1 or PRI (Primary Rate Interface).

Both T1 and PRI carry 24 pulse code modulation (PCM) signals using
time-division multiplexing (TDM) at an overall rate of 1.544 Mbps. Voice
T1 provides twenty-four 64K channels with robbed bit signaling. PRI
provides twenty-three 64K channels, using one 64K channel for D channel
messaging.

The Triton T1/PRI board is used to provide voice processing resources for
AltiWare OE, similar to the way Quantum telephony boards are used for
analog trunks and extension lines. AltiWare OE uses DSP engines residing
on the Triton T1/PRI board to perform the voice processing functions
needed for either T1 or PRI service. Quantum and Triton boards are
connected via MVIP connectors.

For information on how to install Triton T1/PRI boards, refer to the Quick
Installation Guide provided with every board package.

Important:

Configuration for Triton T1/E1/PRI boards can only be done at

the local system. These boards cannot be configured by a
remote AltiAdmin.

Service Parameters for T1

To subscribe to T1 service, certain parameters are required to establish
service. The information provided below identifies the recommended and
supported parameters for T1 service.

T1 Service Request Information

When ordering T1 service, provide the following service request
information:

Equipment Information

Product Manufacturer - AltiGen Communications, Inc.

Product Name - AltiServ PBX Phone System

Summary of Contents for AltiWare OE 4.6







































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands