ABB IRB 390 Product Manual Download

Page: 91 / 346

Description

Spare part number

Axis mark label, axes 1, 2 and 3

3HAC040066-001

Axis mark label, axes 4 and 5

3HAC076731-001

Warning label
Hot surface

3HAC076469-001

Instruction label
Lifting of robot

3HAC076465-001

Information label
Battery

3HAC055008-001

FlexPicker label

3HAC075329-001

Required tools and equipment

Visual inspection, no tools are required.

Inspecting, labels

Note

Action

DANGER

Turn off all:

•

electric power supply

•

hydraulic pressure supply

•

air pressure supply

to the robot, before entering the safeguarded space.

Inspect the labels, located as shown in the figures.

Article numbers for the labels and
plate set is specified in

Inspecting

the information labels on page 90

Replace any missing or damaged labels.

Product manual - IRB 390

3HAC066566-001 Revision: B

4 Maintenance

4.3.2 Inspecting the information labels

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands