ABB IRB 390 Product Manual Download

Page: 202 / 346

Refitting the lower arm to the delta unit

Note

Action

Sealing washer: 3HAC062123-001.

xx2000000861

Fit the sealing washer to the lower arm.
Replace the sealing washer if damaged.

Anti-seize paste: 3HAC070875-002
(Molykote P1900)

xx2000000684

Lubricate the lower arm thread.

Note

The surface under the thread head must be dry
and not contain grease.

Lower arm / parallel bar:
3HAC060138-001.

xx2000001063

Fit the lower arm.
Make sure the sealing washer is in place.

Continues on next page

202

Product manual - IRB 390

3HAC066566-001 Revision: B

5 Repair

5.5.1 Replacing the lower arm

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands