ABB IRB 390 Product Manual Download

Page: 126 / 346

5.4 Base

5.4.1 Replacing the base unit

Location of the base unit

The base unit is located as shown in the figure.

xx2000000306

Summary of the replacement procedure

This is a brief summary of the replacement procedure, containing the major actions
to be performed.

1 Remove the telescopic shaft/shafts including the universal joints.

2 Remove the lower arms and delta unit.

3 Remove the upper arms.

4 Lift down the base unit to a workbench.

5 Move the SMB unit, the cable harness, and the axis-4 and axis-5 motor and

gear units from the old base to the new.

Also move the axis-1, axis-2 and axis-3 motors from the old base to the new,
if the base spare part is ordered without motors.

6 Refit the new base unit to the robot frame.

7 Refit the upper arms.

8 Refit the lower arms and delta unit.

9 Refit the telescopic shaft/shafts.

Continues on next page

126

Product manual - IRB 390

3HAC066566-001 Revision: B

5 Repair

5.4.1 Replacing the base unit

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands