ABB IRB 390 Product Manual Download

Page: 127 / 346

Required spare parts

Note

The spare part numbers that are listed in the table can be out of date. See the
latest spare parts of the IRB 390 via myABB Business Portal,

www.abb.com/myABB

Level

Note

Article number

Spare part

The spare part includes following
parts:

•

base

•

axis-1, axis-2 and axis-3
gear

•

axis-1, axis-2 and axis-3
motor

•

brake release button

3HAC060564-003

Base unit

The spare part includes following
parts:

•

base

•

axis-1, axis-2 and axis-3
gear

•

brake release button

3HAC060563-003

Base unit

Required consumables

Note

Article number

Consumable

Isopropanol

Cleaning agent

Molykote P1900

3HAC070875-002

Anti-seize paste

Other spare parts

Following parts are affected during the replacement procedure. Replace if damaged
or lost.

Note

Article number

Spare part

Base unit top cover.

3HAC058649-003

Sealing washer

M8x40 stainless steel/A4-80

3HAC060233-008

Hexagon flange bolt

M8 hygienic. If the rubber is
damaged, replace the washer
with new for hygienic purpose.

3HAC058626-004

Washer

Between base unit and upper
arm.

3HAC062067-001

Sealing ring

3HAC043799-001

Washers, 12 pcs

For the upper arm cover.

3HAC058619-001

Gasket

To the lower arm.

3HAC062123-001

Sealing washer

Between universal joint and tele-
scopic shaft/base unit/delta unit.

3HAC060200-001

Friction shim

Between universal joint and tele-
scopic shaft/base unit/delta unit.

3HAC060263-001

Sealing ring

Continues on next page

Product manual - IRB 390

127

3HAC066566-001 Revision: B

5 Repair

5.4.1 Replacing the base unit

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands