ABB IRB 390 Product Manual Download

Page: 238 / 346

Note

Article number

Equipment

Included in robot delivery.

xx1900002148

Used with an interchangeable
head torque wrench (not included
in delivery).
Interface: 14x18 mm.

3HAC073854-001

Torque wrench head, open-end in-
sert

Interchangeable head torque
wrench

Delivered as a set of calibration
tools.

3HAC055412-001

Calibration toolbox, Axis Calibra-
tion

Content is defined in section

Standard toolkit on page 336

Standard toolkit

Removing the motor

Use these procedures to remove the axis-1, axis-2 or axis-3 motor.

Preparations before removing the axis-1, axis-2 or axis-3 motor

Note

Action

Jog the robot to synchronization position.

DANGER

Turn off all:

•

electric power supply

•

hydraulic pressure supply

•

air pressure supply

to the robot, before entering the safeguarded
space.

Continues on next page

238

Product manual - IRB 390

3HAC066566-001 Revision: B

5 Repair

5.6.1 Replacing the axis-1, axis 2 and axis-3 motor

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Related manuals for IRB 390

Brands by name

Popular brands