ABB IRB 390 Product Manual Download Page 200

Page: 200 / 346

Note

Action

Interchangeable head torque
wrench

Loosen the upper shaft from the upper arm by
loosening the nut.

Torque wrench head, open-end in-
sert: 3HAC073854-001

xx1900002152

Use an interchangeable head torque wrench and
the open-end head insert.

Sealing washer: 3HAC062123-001.

xx1900001796

Remove the lower arm.
Save the sealing washer for refitting, or replace
it if damaged.

Refitting the lower arm

Use these procedures to refit the lower arm.

Refitting the lower arm to the upper arm

Note

Action

Sealing washer: 3HAC062123-001.

xx2000000861

Fit the sealing washer to the lower arm.
Replace the sealing washer if damaged.

Continues on next page

200

Product manual - IRB 390

3HAC066566-001 Revision: B

5 Repair

5.5.1 Replacing the lower arm

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Brands by name

Popular brands