ABB IRB 390 Product Manual Download Page 163

Page: 163 / 346

Removing the top cover

Note

Action

xx2000001006

Disconnect connector R1.MP from the base.

CAUTION

Clean cover from metal residues before opening.
Metal residues can cause shortage on the boards
which can result in hazardous failures.

xx1900000407

Remove the SMB battery cover.

Tip

The battery cover is removed to see the battery
position during refitting of the top cover.

xx1900000469

Remove the cover by removing the screws and
washers. Also remove the sealing.

Removing the SMB unit

Note

Action

ELECTROSTATIC DISCHARGE (ESD)

The unit is sensitive to ESD. Before handling the
unit read the safety information in section

The

unit is sensitive to ESD on page 42

Continues on next page

Product manual - IRB 390

163

3HAC066566-001 Revision: B

5 Repair

5.4.3 Replacing the SMB unit

Continued

Summary of Contents for IRB 390


























































































































































































































































































































































Search results

Summary of Contents for IRB 390

Reviews:

Brands by name

Popular brands

ABB IRB 390, Product Manual

Search results

Summary of Contents for IRB 390

Reviews:

Brands by name

Popular brands